When you have finally laid down the necessary concreting works for your floor, you need to see to it that you have the right covering or veneer on top so that it can look better and it will be protected as well. You can ensure that the right kind of garage floor epoxy, stain or paint will help keep your concrete surface be protected from the harsh chemicals. You should always do careful planning when it comes to the garage floor epoxy installation that you want to do so that you can always maintain a healthy and clean surface all the time.
There are so many factors that will affect the durability and strength of the concrete flooring that you have. It is an important consideration that you will look carefully on what you can do to ensure that you will get the right and perfect outcome for your floor.
Garage Floor Epoxy: Builder Tips for Quality Installation
Chemicals Can Destroy a Garage Floor
Chemicals can react with the surface of your concrete floor and cause it to deteriorate over time. Road deicing salts that stick to the underside of the snow under your car and then fall off onto the floor as they melt can create problems. Fluids leaking from vehicles, like anti-freeze, can also become a problem. How about all of the cleaning solutions, fertilizers or different types of fuel you store in your garage? These can all cause your floor to flake, crack and crumble over time. So providing a layer of protection on top of the floor can really help prolong its life.
Concrete Replacement
If you don’t protect your garage floor concrete and it deteriorates, it can get quite expensive to replace. Typically, garage floor slabs are poured to a four inch thickness. So removal can take some serious effort with jack hammers, laborers and a small skid steer (a.k.a. Bobcat). In many cases, the removal will cost in the range of $3-$5 per square foot. If you have an average sized garage of 400 square feet, removal alone will set you back $2000. Installing the new concrete will typically cost between $3.5 and $5 per square foot. Then figure in reinstalling the steps into the home and the possible damage to the overhead garage door rails, you’re looking at a big project. So even if you get very good pricing for your garage floor replacement, it will still set you back a minimum of $3000.
Problems with Garage Floor Epoxy, Stain, or Paint
So installing a protective coating over your garage floor can pay off over the long run. But keep in mind, this is typically a time consuming job. You’re not going to run down to the hardware store, pick up a couple gallons of paint and roll it on. This won’t last…guaranteed. The most common types of failures are flaking and peeling of the new surface. And the most common place that the failure occurs is under the tires. Remember, your car’s tires can get hot after driving. This heat can cause the garage floor epoxy, paint or stain to delaminate from the surface of the concrete. Check out more info here…
It would also be necessary that you will look at getting the perfect concrete staining to be applied on your flooring, as it is one that can make your floor look like a piece of art. You will really have concrete flooring that will be an envy of everyone, as it is one that will look too gorgeous for anyone to see. There are so many great ways which you can do so that you can get everything settled once and for all.
Concrete Staining Tips, Techniques, Advice, and Troubleshooting Help
Xylene is typically used when there’s a major amount of moisture trapped and/or the moisture is deep, for instance, if the 2nd coat of sealer was applied before the first coat had completely dried clear, or if applied too heavily, or if applied during very high humidity thereby trapping the moisture deep into the sealer. If the moisture is over a major part of the area but it’s trapped in the surface and not deep, simply spraying the xylene onto the surface will do it because the xylene will quickly open the sealer up and encourage the moisture to escape and then dry back down clear. This works many times for moisture trapped deep as well.
If just spraying on Xylene doesn’t work, then you’ll need to use scrub brushes with the xylene and strip the sealer off, so you can begin again.
Remember that if the temperature is cold or the humidity is high then that slows and/or prohibits the moisture from escaping. However, if it’s very hot then the sealer wants to dry back down quicker, perhaps faster than the moisture can escape. So what you want is a warm temp and low humidity as best as you can get it. The humidity is the primary concern. 40% to 50% is a good range, lower is better, but 60% is pushing it and 65% to 70% is a deal breaker. For ideal temps, think tropical. 70 to 80 degrees is great, 90 to 95 or so on the high side is about it, and on the low side, 60 degrees is ok but 50 degrees is pushing it and 45 is absolutely the lowest. This site has more information as well: http://ift.tt/2m2kSu3.
All these are important matters that you need to very much understand so that you can get the right kind of concreting job for your homes. Reading the right articles are essentially handy especially when you want to get the right protection of your concrete flooring and for you to find how you can enhance the aesthetics of your concrete floor.
The post Troubleshooting Help When It Comes To Concreting appeared first on AAA Concreting.
No comments:
Post a Comment